Quote Being Processed…

Taking a deep dive

🏊 Configure 📋 My Summary 📩 Request Quote

All Users Pending Engineers Quote Requests Analytics Settings

⚠ Note

The distances from the pool to the boundary lines and buildings are approximate and need to be confirmed with a site-specific site plan. Site-specific site plan/s need to be uploaded to the Request Quote tab.

The property information may take a few seconds to load once the pool is placed.

OK

⚠ Pool Setback

The pool edge/s is encroaching on the required boundary setback or is too close to the existing building. The pool location would need to be confirmed with a Specific Engineering Design.

OK

⚠ Underground Services

Potential pool clash with underground services on this site. The pool location would need to be confirmed against the actual service locations and depths before excavation. It is recommended that the pool be checked by a Suitably Qualified Engineer.

OK

Step 1 of 8

Welcome

…

Skip Back Next

Terms & Conditions

×

Last updated:

1. Nature of the Software

Pool Builder (the “Software”, “website” or “tool”) is provided solely as a preliminary planning and visualisation aid. It is intended to assist a Qualified Chartered Professional Engineer (CPEng) and is not a substitute for professional engineering design, judgement, site verification, or certification. You use the Software at your own discretion and risk.

2. Professional Engineer Review Required

Any output, drawing, measurement, site plan, quote or report generated by the Software must be independently reviewed, checked, and signed off by a Qualified Chartered Professional Engineer (CPEng) before being used for any design, construction, consenting, or other purpose. That engineer is responsible for verifying all information and assumes professional responsibility for any work derived from it. The Software is only a tool to assist, and does not replace, that engineer.

3. Information is Approximate

All information presented by the Software — including but not limited to property boundaries, building outlines, underground service locations, distances, dimensions, areas, orientations, pool specifications, and aerial imagery — is indicative and approximate only, is sourced from third-party data that may be inaccurate, incomplete or out of date, and must be independently confirmed on site and against authoritative sources before any reliance is placed on it. Underground service locations in particular must be confirmed with the relevant network providers before any excavation.

4. Not for Building Consent Applications

The information provided in any quote or report produced by the Software is not to be used for Building Consent (BC) applications, or any statutory or regulatory submission, without the express approval and certification of a Qualified Chartered Professional Engineer (CPEng).

5. Limitation of Liability

The creator, designer, developer, author, owner, operator, and any contributors to or suppliers of the Software (together, the “Providers”) accept no responsibility or liability whatsoever for any loss, cost, expense, damage, injury, delay, or claim of any kind — whether direct, indirect, incidental, consequential, or special — arising directly or indirectly from the use of, inability to use, or reliance upon the Software or any of its outputs, data, calculations, drawings, or reports. The Software is provided “as is” and “as available”, without warranties or representations of any kind, express or implied, including (without limitation) any warranty of accuracy, fitness for a particular purpose, or merchantability. To the maximum extent permitted by law, the Providers exclude all such liability. Responsibility for any work, decision, design, quote, or construction based on the Software rests entirely with the user and the reviewing Qualified Chartered Professional Engineer.

6. The Designer / Developer of the Website

The person or entity who designed, developed, built, authored, or programmed this website and Software (the “Designer”) provides it only as a general-purpose assistance tool. The Designer is not a party to any engagement between the user and any client, does not provide engineering, surveying, legal, or professional advice, and does not take responsibility for any damages, losses, errors, omissions, inaccuracies, or consequences of any kind arising from the Software or its use. The Software is only a tool to be used as assistance to, and under the supervision of, a Qualified Chartered Professional Engineer. The user agrees to indemnify and hold harmless the Designer and the other Providers against any claim, demand, liability, or cost arising from the user’s use of the Software or reliance on its outputs.

7. Third-Party Data & Sources

The Software relies on data, imagery, and services supplied by third parties (including, without limitation, mapping, aerial imagery, cadastral/parcel, building outline, and utility/service-network providers). The Providers do not control, verify, or guarantee the accuracy, completeness, currency, or availability of such third-party data, and accept no liability for any error, omission, outage, or change in it. The user is responsible for independently verifying all such information against authoritative, current sources.

8. No Professional Relationship

Use of the Software does not create any client, professional, fiduciary, agency, partnership, or advisory relationship between the user and the Providers or the Designer. Nothing produced by the Software constitutes engineering, surveying, planning, legal, or financial advice.

9. Changes to These Terms

The Providers may update or amend these Terms & Conditions at any time. Continued use of the Software after any change constitutes acceptance of the revised Terms. These Terms are governed by the laws of New Zealand.

10. Acknowledgement

By creating an account and using the Software, you acknowledge that you have read, understood, and agree to these Terms & Conditions, and that you accept the responsibilities and limitations set out above.

Close